----- Original Message -----
Sent: Thursday, May 22, 2003 8:40
PM
Subject: Re: [PSUBS-MAILIST] Main
ballast.
"The vents for the fore and aft soft MBT have to
be mounted at the top of the tanks in order to release the air above the
water. Since the MBT's top is the same height as the top of the
hull, the piping and valves had to be located at the height of the conning
tower. "
Ok, so if the sub is sitting on the water on
the surface, the air in the MBT's should be under some pressure since the
weight of the sub is forcing it down, and thus forcing water into the
bottom of the MBT's, and thereby displacing the air in them and
compressing it until it achieves equilibrium and the sub floats,
right? I understand why the valve has to be at the top of the MBT,
but your piping doesn't have to be at the same level as the valve,
right? If I reckon right, the somewhat pressurized air in the MBT's,
once the valve is opened, should rush right out no matter where your
piping is, as long as the MBT is able to flood completely, right?
At the depths I'm aiming for (ummm....50
feet?) I hadn't thought that my valve configuration would pose
a problem as far as withstanding the pressures involved. I may re-do
it anyway though.
Chris
"Dan H." <JMachine@adelphia.net>
wrote:
Chris,
First I have to say, I didn't design it but
from what I see in the over all design, and knowing the designer, I
think the valving was done this way for safety and simplicity. All
other valves except these vent valves are located within the
hull.
Since each of these vent valves run from an
external tank to outside the hull, each valve would have two through
hulls for the piping. Better three, quarter turn through hulls,
then six pipe through hulls, more fittings and a still three valve stem
seals inside the hull.
The vents for the fore and aft soft MBT
have to be mounted at the top of the tanks in order to release the air
above the water. Since the MBT's top is the same height as the top
of the hull, the piping and valves had to be located at the height of
the conning tower. It would be cluttered to have these valves and
their piping inside the conning tower. On both K subs, the MBT
vent valves are taken apart and altered with long stems that screw right
on to a special threaded replacement for the packing nut that is welded
in through the conning tower wall. It makes a clean package and
has double O-ring seals for added safety. Even if the valves
get sheared off, the stems have shoulders that prevent then from blowing
through to the inside.
The less holes in the hull the
better.
----- Original Message -----
Sent: Wednesday, May 21, 2003
10:33 PM
Subject: Re: [PSUBS-MAILIST] Main
ballast.
Hey Dan,
Just wondering, what is the reason for
mounting the valves external to the hull on the K-350? Is it
because it's easier to put the actuating shafts in a thru-hull and run
that through the hull to the valve, rather than mount the valves
inside the hull with the air lines and air supply and run the air
lines through the hull to the MBT's? Or something else I
missed?
Thanks,
Chris Nugent
"Dan H."
<JMachine@adelphia.net> wrote:
Pierre,
On
the K-350 the "hard ballast tank" is located under the hull. There
is a
shaft that runs through the hull with a flex coupling on it
that is directly
above a quarter turn valve on the sea water
opening of the hard ballast
tank. A quarter turn of this threw
hull shaft turns the ball valve
directly.
The "soft
ballast tanks" are of fiberglass and are located fore and
aft.
They are opened to sea water all the time. The vent air is
controlled with
quarter turn ball valves located on the conning
tower. The valves are also
located external but are altered with
special long stems so they are
controlled from inside the conning
tower. The valves are connected to the
top of the tanks with
tubing. The valves are mounted high in the tower and
vent from
the tops of the tanks.
Hope this is what your looking
for.
Dan H.
----- Original Messa! ! ! ge -----
From:
"pierre&marie"
To:
Sent: Wednesday, May 21, 2003
6:31 PM
Subject: [PSUBS-MAILIST] Main ballast.
> Hi
People!
>
> How do you "plug" the main ballast tank to
adjust buyoncy (man, that word
is
> killing
me...)
>
> I'm trying to figure a way to use a 5/3
pneumatic valve. It would be easy
to
> use to adjust
bouyancy. But, I can't have the plumbing right at
the
moment.
>
>
> Any advise? Somebody know how
it's done in a K-350?
>
> Thanks!
>
> Pierre
Poulin
> "At last the sun is
here!"
>
>
>
Do you Yahoo!?
The
New Yahoo! Search - Faster. Easier. Bingo.
Do you Yahoo!?
The
New Yahoo! Search - Faster. Easier. Bingo.