[PSUBS-MAILIST] Flush Mount Valves in MBT's

hank pronk hanker_20032000 at yahoo.ca
Mon Dec 9 07:23:10 EST 2013


Jim,
Yes that is the valve, you are right that they are the same height.  if you invert them then the air supply fitting is pointing down.  Then you will have a cleaner surface on the mbt. 
Hank



On Sunday, December 8, 2013 6:38:53 PM, "jimtoddpsub at aol.com" <jimtoddpsub at aol.com> wrote:
  
Hank, is this the one you were referring to?  If so, it looks same height either way. 
Jim 
http://www.ebay.com/itm/ROSS-SERIES-27-REMOTE-AIR-CONTROLLED-VALVE-2754A6011-1-/190913302565?pt=LH_DefaultDomain_0&hash=item2c7351d025 

  
-----Original Message-----
From: hank pronk <hanker_20032000 at yahoo.ca>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Sent: Sun, Dec 8, 2013 7:12 pm
Subject: Re: [PSUBS-MAILIST] Flush Mount Valves in MBT's


Joe  
The valve you want is on ebay  ross series 27 remote controlled valve 1inch 
the valfe is air powered and a very low profile if inverted. 
Hank 



On Sunday, December 8, 2013 4:26:39 PM, "jimtoddpsub at aol.com" <jimtoddpsub at aol.com> wrote:
  
 
Hi Joe, 
  
I'm trying to keep the top of the MBTs as sleek as possible, so the vent valve will either be flush with the exterior or have only a slight bulge.  I can live with a liter or so of residual air, but I would like to minimize it.  The main reason is that it will compress to 1/3 of that at 100 feet and 1/10 at maximum depth.  It would certainly be nicer to have as little residual air as possible so you wouldn't have even that much change in buoyancy as you descend.  I have a couple of VBTs as well. 
  
Two other design solutions are (a) taper the top of the MBT toward the vent, or (b) if the top of the MBT is flat, add just enough non-compressible material to the inside top of the tank to exclude an air pocket.  Taper it.  Syntactic foam would be great. 
  
Yup, CAD is certainly the eighth wonder of the world.  I think the greatest benefit is being able to alter one number and have the recalc flow all the way through without having to redraw.  By the way, Wilbur only lived nine years after the first flight in 1903, but Orville lived to see operational jet aircraft.  He died in 1948. 
  
Jim   
-----Original Message-----
From: Joe Perkel <josephperkel at yahoo.com>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Sent: Sun, Dec 8, 2013 4:07 pm
Subject: Re: [PSUBS-MAILIST] Flush Mount Valves in MBT's


 
Jim, 
 
I don't know quite yet, I just know I would want it clean and as low profile as possible. I'm toying with two separate designs, one that incorporates significant exostructure, the other less so. The fleet boat manual shows how the vents were routed high up into and hidden within the casing, something I could consider for saddle MBT's on an Alvin Jr type of configuration. For a reduced scale Seehund replica, (the other design), a flush mount is more of a consideration. At first glance, the extra reserve buoyancy makes the Alvin Jr. design a better choice for my conditions, the Seehund is really just an enjoyable distraction. 
 
Good points both ref reliability and residual air allowances. I can pinpoint such volumes quite accurately in the software. I just love CAD, everyone from the Wright Brothers to John Holland and everyone in between would say we have it too easy now! 
 
Joe
 
 
On Sunday, December 8, 2013 4:00 PM, "jimtoddpsub at aol.com" <jimtoddpsub at aol.com> wrote:
  
 
Joe, 
Minimizing residual air in an MBT would be a consideration for me, but it would be the last consideration after first determining the best valve design for function, controlability, durability, and maintenance.  At that point you can set the air vent as close to the top of the tank as possible and allow for any residual air in your design calculations.  I expect the size of the bubble will be minimal.  In your design, how much of a consideration is the amount the valve assembly projects above the top of the tank? 
Jim 
  
  
-----Original Message-----
From: Joe Perkel <josephperkel at yahoo.com>
To: personal_submersibles <personal_submersibles at psubs.org>
Sent: Sun, Dec 8, 2013 2:13 pm
Subject: Re: [PSUBS-MAILIST] Flush Mount Valves in MBT's


Hi Alan,

That's similar to a Kingston isn't it? That shape would assure complete venting, one would have to be assured of fail safe reliability in whatever was used. I would like a normally closed fail safe mode in whatever style best assures sealing.

Joe



Sent from Yahoo Mail for iPad  



________________________________
 From:  Alan <alanlindsayjames at yahoo.com>; 
To:  Personal Submersibles General Discussion <personal_submersibles at psubs.org>; 
Subject:  Re: [PSUBS-MAILIST] Flush Mount Valves in MBT's 
Sent:  Sun, Dec 8, 2013 7:10:19 PM 
 

Hi Joe, 
While thinking about the ballast valve, it occurred to me that 
the drain pop up plugs found in modern bathrooms, are very 
similar to what we want. 
https://www.google.co.nz/search?client=safari&hl=en-gb&biw=768&bih=928&tbm=isch&sa=1&ei=47ukUvT-EsqhkwWt04DoAQ&q=drain+pop+up+waste&oq=drain+pop+up+waste&gs_l=img.3...46028.57398.0.58014.39.28.0.2.2.0.324.3866.8j5j4j5.22.0....0...1c.1.32.img..27.12.2132.cLok805IcCc
Hope that link came out OK. It was an image search on DRAIN POP UP WASTE 
They would need to work upside down for our application, so they would be flush on the 
inside of the ballast tank (eliminating an air trap) but extend a bit above the ballast tank. 
Some models look like you could just stick an air line straight on to them, & with a spring  
In them, they would work. 
There may be some model that is ideal. 
Alan
Sent from my iPad 

On 8/12/2013, at 2:09 PM, Joe Perkel <josephperkel at yahoo.com> wrote:

 
I need a little help understanding the installation of
remotely operated pneumatic valves in soft tanks. I’ve been looking at various
products on the Net, and from what I see, there doesn’t seem to be an off the
shelf remotely operated valve that would install flush and fully vent the tank.
What I’m looking for is a flush mount and a clean installation which eliminates
the exterior tubing routed to the conning tower.  
>Am I missing a valve type or installation that would
accomplish this? 
>Thanks 
>Joewith         
_______________________________________________
>Personal_Submersibles mailing list
>Personal_Submersibles at psubs.org
>http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>         
_______________________________________________
Personal_Submersibles mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles      

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
 

        
_______________________________________________
Personal_Submersibles mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles      

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
 

       
_______________________________________________
Personal_Submersibles mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles      

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20131209/30922756/attachment-0001.html>


More information about the Personal_Submersibles mailing list