[PSUBS-MAILIST] conical transitions

Hugh Fulton hc.fulton at gmail.com
Tue Jan 7 19:51:17 EST 2014


I think I missed the point thinking the sphere end was part of the Hull.

What Vance is saying is like a leg tube into a sphere where he is quite correct.  Sorry missed the point.

 

Hugh

 

From: Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] On Behalf Of vbra676539 at aol.com
Sent: Wednesday, 8 January 2014 1:30 p.m.
To: personal_submersibles at psubs.org
Subject: Re: [PSUBS-MAILIST] conical transitions

 

Wouldn't you figure that like an ASME nozzle--like a conning tower? 

Vance



-----Original Message-----
From: brian <brian at ojaivalleybeefarm.com>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Sent: Tue, Jan 7, 2014 4:46 pm
Subject: Re: [PSUBS-MAILIST] conical transitions

Would the same apply to a cylinder to sphere transition?  On mine I'm planning on a 1" thick collar welded to the sphere then the cylinder to that .

brian

-----Original Message-----
From: "Hugh Fulton" <hc.fulton at gmail.com>
Sent 1/7/2014 12:45:24 PM
To: "'Personal Submersibles General Discussion'" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] conical transitions

Hi All,  

I have been through that problem and you have to have a good sized stiffener there of some sort.  I could not afford the room as an intrusion of internal space.

This is the solution and the angle of the additional reinforcing cone is 22.5 degrees being half the 45 degrees of the cone.  This survived an FEA analysis.  The end of the cone is where my window was attached.

This was a 48” shell  .  Regards,  Hugh

 

 

 

 

 

 

From: Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org <mailto:personal_submersibles-bounces at psubs.org?> ] On Behalf Of Jon Wallace
Sent: Wednesday, 8 January 2014 8:10 a.m.
To: Personal Submersibles General Discussion
Subject: Re: [PSUBS-MAILIST] conical transitions

 


Joe, ABS says stiffened cones are to have their ends bounded by two heavy stiffeners each located as close as possible to the point of cone-to-cylinder transition.

The stiffener is not located on the weld line but as close as possible to it.

Jon




On Tuesday, January 7, 2014 5:30:16 AM, Joe Perkel  <mailto:josephperkel at yahoo.com> <josephperkel at yahoo.com> wrote:


David,

Is that T ring directly on the weld line, or offset any distance?

Joe <http://overview.mail.yahoo.com/?.src=iOS> 

Sent from Yahoo Mail for iPad

 




__________ Information from ESET NOD32 Antivirus, version of virus signature database 9257 (20140106) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com



__________ Information from ESET NOD32 Antivirus, version of virus signature database 9257 (20140106) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 

__________ Information from ESET NOD32 Antivirus, version of virus signature database 9262 (20140107) __________

 

The message was checked by ESET NOD32 Antivirus.

 

http://www.eset.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20140108/8df3ce95/attachment-0001.html>


More information about the Personal_Submersibles mailing list