[PSUBS-MAILIST] annealing acrylic

hank pronk hanker_20032000 at yahoo.ca
Mon Mar 24 20:39:27 EDT 2014


Brian,
Do you have the Stachiw book of Acrylics, I can send you mine if you don't have a copy.  There is some pretty important stuff in there.
Hank



On , hank pronk <hanker_20032000 at yahoo.ca> wrote:
  
Brian,
How thick is your acrylic?  should take more than a night?
Hank



On Monday, March 24, 2014 6:33:09 PM, Brian Cox <brian at ojaivalleybeefarm.com> wrote:
  
Yes, I have the annealing schedules.  I have an electric oven and two digital thermometers, one I'm going to put in a piece of acrylic and the other one I'm going to use to monitor the oven temperature itself .  I'm worried that the thermometer in the acrylic won't register until it gets heated throughout, and so then the oven temp might go higher than it should.  So between the two readouts I can heat it gradually up.  It'll be a long night.

Brian

--- hanker_20032000 at yahoo.ca wrote:

From: hank pronk <hanker_20032000 at yahoo.ca>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] annealing acrylic
Date: Mon, 24 Mar 2014 17:22:32 -0700 (PDT)


Brian,
Are you going to anneal your windows yourself?  
Hank 



On Monday, March 24, 2014 6:03:10 PM, Brian Cox <brian at ojaivalleybeefarm.com> wrote:
  
Used my polarized lenses on the newly cut piece and it appears clouded throughout the whole piece.  Where as another piece I have, you can clearly see a stress area around where it has been drilled. 

Brian


--- emile at airesearch.nl wrote:

From: "Emile van Essen" <emile at airesearch.nl>
To: "'Personal Submersibles General Discussion'" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] annealing acrylic
Date: Mon, 24 Mar 2014 22:40:46 +0100


As far as I know it is
only cast. 
  
Regards, Emile 
    
Van:Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] Namens Brian Cox
Verzonden: maandag 24 maart 2014
20:37
Aan: PSubs 
Onderwerp: [PSUBS-MAILIST]
annealing acrylic 
  
I'm planning on annealing my viewports,  does anyone
know if the acrylic from the factory is pre-shrunk ? 
  
Brian _______________________________________________
Personal_Submersibles mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles  
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


    _______________________________________________
Personal_Submersibles mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles 

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20140324/395bd5dd/attachment.html>


More information about the Personal_Submersibles mailing list