[PSUBS-MAILIST] LED Lights

Clifford Redus via Personal_Submersibles personal_submersibles at psubs.org
Thu Jul 23 16:17:52 EDT 2015


Now that Jon has the forum site set up for the LED light project, my
suggestion is to move the discussion to the forum site called out in Jon's
email.  BTW, I have uploaded to the site the wiring diagram and housing
drawings for the 5000 Lumen light that was designed by the ME students I
was mentoring last year.

Cliff

On Thu, Jul 23, 2015 at 2:55 PM, Ken Martindale via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Doing the dimming electrically is easy but the problem is the extra wiring
> and where do you mount the Potentiometer?
>
>
>
> We can include the wires in the cable for use as an option this also
> complicates the cabling. Instead of two wires we would require 4 wires.
>
>
>
> Personally I also like the dimming since it will extend the time you can
> use it out of the water. Anybody also like or dislike? Cliff would like to
> delete.
>
>
>
> You guys be sure to keep reading the spec. it will have almost daily
> updates for a while.
>
>
>
> Ken
>
>
>
> *From:* Personal_Submersibles [mailto:
> personal_submersibles-bounces at psubs.org] *On Behalf Of *Alan James via
> Personal_Submersibles
> *Sent:* Thursday, July 23, 2015 3:31 PM
> *To:* Personal Submersibles General Discussion <
> personal_submersibles at psubs.org>
> *Subject:* Re: [PSUBS-MAILIST] LED Lights
>
>
>
> Cliff, Ken,
>
> I like the dimming option. The 10,000 lumens may be too much light in
>
> some low visibility conditions where there is a lot of back scatter.
>
> The 5,000 lumen option may act like a fog light.
>
> Also I am thinking of having lights mounted to the side which may not
>
> need to be as intense.
>
> Depth rating.... looking at the drawings of various 10,000 meter light
> housings,
>
> it seems simple to achieve a reasonable depth without much more cost.
>
> Potting the board..... I would be careful about what was potted in case
> some of the
>
> components needed to get rid of a bit of heat.
>
> Mechanical housing..... with you on that one Cliff. Like the idea of the
> recessed light.
>
> Alan
>
>
> ------------------------------
>
> *From:* Clifford Redus via Personal_Submersibles <
> personal_submersibles at psubs.org>
> *To:* Personal Submersibles General Discussion <
> personal_submersibles at psubs.org>
> *Sent:* Friday, July 24, 2015 4:06 AM
> *Subject:* Re: [PSUBS-MAILIST] LED Lights
>
>
>
> Ken, good first pass at the specs.  Below are comments.  BTW, I will post
> these here as I have not been able to get the activation code back yet on
> registering at the forum.
>
>
>
> Item 2.1 DC Voltage.  If it were me, I would stick with nominal battery
> bank voltages of 24 and 36 VDC.  When I switch to MK 101 thrusters, I
> dropped my main battery bank voltage to 36VDC my instrumentation bus is
> 24VDC.  Would need a single fuse holder to accept fuses to handle different
> nominal voltages.
>
>
>
> Item 4.0 Depth Requirement.  In the spirit of keeping cost down, I think
> 500 meters (1640 ft) would be more than enough.  I know Scott is designing
> a deep diving boat but is any one else shooting for more than 500m?
>
>
>
> 6.0 Dimming.   I would omit the ability to dim the light.  Yes I know it
> is easy from an electrical point of view but it forces us to go with more
> pins on the subsea connector.  I am thinking on installing multiple lighs
> so I could just control on/off for each light.  I could go either way on
> this but in the spirit of KISS, I vote to omit dimming.
>
>
>
> 8.3 Ports  I would change plastic to acrylic.  I don't think we will end
> up here but if we do, we can use PVHO flat view port calcs to size the
> acrylic lens.
>
>
>
> 9.0 Printed Wiring Boards.  I really like the way the Minn-Kota motor
> controller PWBs are potted.  Rather than using the spray on hydrophobic
> coatings, to me we should pot the board (accept for access to fuse).
> Therefore suggest changing the word coated to potted.
>
>
>
> 11.0 Mechanical Housing.  I suggest.  The LED panel light and PCB shall
> be contained in a single 1-atm flange mounted cylindrical housing with a
> low profile that can be recessed in a FRP shell with attachment screws from
> the rear of the flange.  The housing should contain a single 29 LED Array
> rated at 10,000 lumens  with a rated power of  91-140 lumens/W (109-71W).
> Mounting holes will be provided for an optional SS yoke style support
> bracket.
>
>
>
> Material: Hard anodized 6061-T6 or 7071-T6  TBD (I have a grey beard
> machinist friend that owns a machine shop.  He loves 7071-T6 as it is a
> dream to machine and stronger than 6061-T6.
>
>
>
> On Thu, Jul 23, 2015 at 9:52 AM, Ken Martindale via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
>
>
> Cost is critical. The electronics should be a small part of the cost. The
> housing might be the most expensive.
>
>
>
> Hope you guys are reading the specification.
>
>
>
> Ken
>
>
>
> *From:* Personal_Submersibles [mailto:
> personal_submersibles-bounces at psubs.org] *On Behalf Of *Clifford Redus
> via Personal_Submersibles
> *Sent:* Thursday, July 23, 2015 10:18 AM
> *To:* Personal Submersibles General Discussion <
> personal_submersibles at psubs.org>
> *Subject:* Re: [PSUBS-MAILIST] LED Lights
>
>
>
> Jon, thanks for setting up the forum.  I am assuming we can post files as
> well.
>
>
>
>  I agree low cost is important but having a functioning light is as well.
> OTS LED utility lights like that one you noted are not an option unless
> they can be potted.  To me the best way to keep the cost low, is to publish
> construction drawings of a 1-atm  DIY housing that a psubber could machine
> or have machined by a friend, and publish a design of a PCB that could be
> easily fabricated using  one of the PCB online sites like  ExperessPCB
> www.expresspcb.com and DIY populate the board.  As a group, we design and
> build a prototype that I can test in my shop. If it works as designed, then
> we post to the psubs site a report, that includes the design drawings,
> circuit diagram, parts list and test results.
>
>
>
> Getting a consciences on the design spec is the first step.
>
>
>
> Cliff
>
>
>
> On Wed, Jul 22, 2015 at 10:11 PM, Jon Wallace via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
>
> My three words of advice...cost, cost, cost.
>
> One measure of a success for this project will be how many people actually
> build/use it.  If it costs more to manufacture than just purchasing
> something like
> http://www.surpluscenter.com/Electrical/Lights/DC-Mobile-Equipment-Lights/12-24-VDC-3120-LUMEN-16-LED-UTILITY-FLOOD-LIGHT-12-999-B.axd
> off the shelf then it's real world application by psubbers may be limited.
>
> Over-spec'ing the design above requirements for typical recreational
> operations (ie 10,000 psi capability) is likely going to drive up the
> cost.  Also, let's remember that "cheap", "low cost", and "good price" are
> relative terms for a diverse group like PSUBS so include realistic
> estimates of parts and manufacturing especially if tooling is required.
>
> Jon
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
>
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20150723/f7c22ab7/attachment-0001.html>


More information about the Personal_Submersibles mailing list