[PSUBS-MAILIST] Got vacuum !

hank pronk via Personal_Submersibles personal_submersibles at psubs.org
Tue Feb 2 08:17:20 EST 2016


Brian,Been there done that,  it is quite easy to fix.  Emile is correct, just take your grinder with a flexible disk and buff the high area down.  Just place the hatch on the land and use feeler gauges to find the gaps and mark them with your chalk.  The fixable disk is very slow at removing material, so you have plenty of control.  I had the same problem with my land on my escape pod and I fixed it easily.  I got it to within .004 and it went to 638 feet.  Don't panic about a little gap.  Just buff then check then buff then check...... oh ya, you can use super coarse disks.Hank 

    On Monday, February 1, 2016 6:29 PM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 Got to straighten this hatch thing out.   Emile suggested that it would be possible to grind/ sand down to get flat, sounds a bit harsh, not sure how I would go about doing that.   I need to get a flat surface, like a granite surface plate or a piece of glass so I can determine flatness.  I knew I shouldn't have welded those hinge flanges on after welding, but I had assurances that it wouldn't deform anything !  Last time I take advice like that !   That side pulled up just slightly so I would have to turn or grind down about 2/3 rds of the hatch by about 75 thousandths to make everything level. Brian  

--- personal_submersibles at psubs.org wrote:

From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Got vacuum !
Date: Mon, 1 Feb 2016 23:18:46 +0000 (UTC)

Any idea when your going to test her?Hank 

    On Monday, February 1, 2016 4:18 PM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 Thanks Hank,  Good feeling ! Brian

--- personal_submersibles at psubs.org wrote:

From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Got vacuum !
Date: Mon, 1 Feb 2016 22:45:04 +0000 (UTC)

Brian A big satisfying mile stone, congratulations!Hank 

    On Monday, February 1, 2016 1:40 PM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 That's encouraging ! Brian

--- personal_submersibles at psubs.org wrote:

From: Emile van Essen via Personal_Submersibles <personal_submersibles at psubs.org>
To: "'Personal Submersibles General Discussion'" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Got vacuum !
Date: Mon, 1 Feb 2016 21:18:33 +0100

Congrats, Vacuum afterbuild or rebuild is a special moment. Carefull grinding andsanding may fix that instead of the lathe. Regards, Emile Van:Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] Namens Brian Cox via Personal_Submersibles
Verzonden: maandag 1 februari 201620:36
Aan: PSubs 
Onderwerp: [PSUBS-MAILIST] Gotvacuum ! HiAll,          My subs sitting with26" of Hg over at my shop !!     Did have a bitof a problem however,  I had to clamp the hatch down because I have aslight warp, probably from a couple of welds done after machining, should beable to remedy that with another trip to the big lathe. Brian Cox_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   _______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   _______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20160202/a3b75887/attachment-0001.html>


More information about the Personal_Submersibles mailing list