[PSUBS-MAILIST] PSUBS light project status

[Alan via Personal_Submersibles]

Thanks Ken,
look forward to the circuit diagram.
Alan


Sent from my iPad

> On 9/07/2016, at 1:39 am, Ken Martindale via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
> 
> Alan,
>  
> The simplest thing to do with my design is to change one of the resistor values for the current required by the Vero or any other LED with the same current.
>  
> This resistor controls the current through the LEDs and is independent of the input voltage and within certain limits independent of the LEDs forward voltage.
>  
> Thanks,
>  
> Ken
>  
> From: Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] On Behalf Of Alan via Personal_Submersibles
> Sent: Thursday, July 07, 2016 8:44 PM
> To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
> Subject: Re: [PSUBS-MAILIST] PSUBS light project status
>  
> Hi Ken,
> I am running a 48V system & haven't found a suitable led driver
> for that input that will run the vero 29 or other 36V leds. 
> Would it be difficult to adapt your driver design to a 48V input?
> I was looking at this switch mode regulator as a possible candidate.
> http://www.ti.com.cn/cn/lit/ds/symlink/lm2593hv.pdf
> I believe you are designing a boost / buck system. I am not sure how much
> extra circuitry is involved in the boost side. Will it be possible to
> simply eliminate the boost circuitry when copying your design?
> Cheers Alan
>  
> 
> 
> Sent from my iPad
> 
> On 8/07/2016, at 4:12 am, Ken Martindale via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
> 
> Thanks Cliff,
>  
> Can you send me your off line E-mail address?
>  
> Thanks,
>  
> Ken
> wmartindale at cfl.rr.com
>  
> From: Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] On Behalf Of Cliff Redus via Personal_Submersibles
> Sent: Wednesday, July 06, 2016 7:24 PM
> To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
> Subject: Re: [PSUBS-MAILIST] PSUBS light project status
>  
> Ken, good news on all fronts.  Welcome back.
>  
> Cliff
>  
> On Wed, Jul 6, 2016 at 3:31 PM, Ken Martindale via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
> To all,
>  
> My wife has been cleared of cancer and I’ll be back on the LED project, starting tomorrow.
>  
> Sorry to drop out for so long,
>  
> Ken Martindale
>  
> From: Personal_Submersibles [mailto:personal_submersibles-bounces at psubs.org] On Behalf Of Cliff Redus via Personal_Submersibles
> Sent: Friday, July 01, 2016 10:40 PM
> To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
> Subject: Re: [PSUBS-MAILIST] PSUBS light project status
>  
> Alec, I was doing the 1 arm can for the light and Ken was doing the electronics.  Ken bailed out so unless someone steps up to take over the LED driver side of the project, we are dead in the water.  If someone could source a small OTS LED driver, I could go forward.  
> 
> On Friday, July 1, 2016, Alec Smyth via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
> Hi gents,
>  
> I have an almost-ready sub but no lights, so was wondering whether to make them per the PSUBS-designed model in the community projects section of the website. I'm in awe of those drawings! However, they show a printed wiring board that is a placeholder for a part still to be designed. I was wondering if that might have happened, or if there might be an ETA?  
>  
> Thanks,
> 
> Alec
> 
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> 
>  
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20160709/a0c26784/attachment.html>