[PSUBS-MAILIST] actuated valves?

hank pronk via Personal_Submersibles personal_submersibles at psubs.org
Sat Apr 15 14:03:36 EDT 2017


I used the red hat valves on my ROV, they are very good quality, but I doubt they are air tight.   

    On Saturday, April 15, 2017 11:36 AM, Alec Smyth via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 There are some Red Hat solenoid valves that are advertised as submersible to 15 feet and have the wires coming out an NPT port, so those could be compensated easily. But they cost a bit more than the air suspension ones.
On Sat, Apr 15, 2017 at 1:27 PM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

Alec,The valves are not air tight, the coil sits in the water.  It comes down to cost really. Sean has a nice idea but your looking at thousands.  An oil bath valve bank will cost  around 500 dollars to set up.  In my mind both will work, I am making an oil bath valve bank for Elementary just because I don't know if it might go in salt water.   We are happy to fill our  motors with oil, why not electro magnets.
Greg,There are tons of air suspension valves  on Ebay with  switch panels even.   I would go with the Valve bank type if your going to oil bath it.
 

    On Saturday, April 15, 2017 10:44 AM, james cottrell via Personal_Submersibles <personal_submersibles at psubs. org> wrote:
 

 Hank,Where to get the valves? Thanks, Greg.

      From: hank pronk via Personal_Submersibles <personal_submersibles at psubs. org>
 To: Personal Submersibles General Discussion <personal_submersibles at psubs. org> 
 Sent: Saturday, April 15, 2017 10:43 AM
 Subject: Re: [PSUBS-MAILIST] actuated valves?
  
Alec,If you want simple, look at electric solenoid valves for venting the tanks.  You can buy 8 valves for 100 dollars.  You can plumb the tanks together to create 4 zones or you can install one valve directly to each tank (12)   The beauty of using more valves is safety.  If one fails, no big issue.  You can wire 3 valves together so only need a 5 wire penetrator.  The nice thing about this idea is it is cheap to experiment with and no modification to the tanks or sub.  you will need check valves on the air feed lines so the tanks are not connected.  No point in venting one zone if it can send or receive air to another zone.  If you are reluctant to use unprotected valves in fresh water, I can say the ones we used on our log salvage ROV never once gave us a problem in two years of operation.  I am talking many thousands of dives, actually one dive every 7 minutes.  If your in salt water then you may want to go with an electric valve bank with four valves where the valve bank is in an oil tank with a bladder mounted behind the CT.   That is how my hydraulic valve works for my new manipulator.  It is fast and easy to set up, and is what I will do for Elementary.  In the mean time you can use cheap valves to figure it all out.  Your entire fix (experiment) can be under 200 dollars, then go to oil bath solenoids.Hank 

    On Saturday, April 15, 2017 6:12 AM, Alec Smyth via Personal_Submersibles <personal_submersibles at psubs. org> wrote:
 

 Hi all,
I'm mulling over options for re-plumbing Shackleton's MBTs. I can go with re-positioned tubing or remotely actuated valves. In principle the tubing is easier, but I'm trying to think through all possibilities before deciding, and just thought of a new option. There's six tanks per side, and the tanks are small so it would be a challenge to put a mushroom valve inside each tank. Besides, that would be a dozen valves. However, I could also do just two valves per side, mounted outside and above the tanks, with very short hoses or tubes leading from three tanks to each valve. There is space, and because the valves would be outside the tanks I have a lot more freedom for the size or geometry of the valves. Maybe even normal ball valves actuated by a little air cylinder. This system would allow for fore-aft and side-to-side control, and would be highly resistant to list-induced water blocking. 
Anyone have thoughts on the KISSest way to control valves? For example, something that could work with unregulated 3K psi air?

Thanks,
Alec

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles


   ______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles


   ______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles


   
______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles



_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170415/37167ad1/attachment.html>


More information about the Personal_Submersibles mailing list