[PSUBS-MAILIST] Pressure Test

james cottrell via Personal_Submersibles personal_submersibles at psubs.org
Sun Jul 9 14:23:16 EDT 2017


Hank,
You may want to contact these guys before spending a lot of $$$
Australia Pressure Vessel Heads 2011 Pty Ltd

  
|  
|   |  
Australia Pressure Vessel Heads 2011 Pty Ltd
   |  |

  |

 

Greg C

      From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
 To: Personal Submersibles General Discussion <personal_submersibles at psubs.org> 
 Sent: Sunday, July 9, 2017 1:23 PM
 Subject: Re: [PSUBS-MAILIST] Pressure Test
   
Greg,Hmmm, just googled EN 26 and it considered machinable even  hardened and tempered, but what does that mean?  Hank 

    On Sunday, July 9, 2017 11:12 AM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 Greg,I asked EE if they could make HY heads and they can but need a quenching tank.  I can not find a supplier that can supply large enough pieces of HY steel  to press a hemispherical head.  EE does not supply anything but 516-70 .  I can ask them but would need to source the material first.  I would need to be sure I can even machine that material, I kinda doubt it?  Hank 

    On Sunday, July 9, 2017 10:36 AM, james cottrell via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 Hank,
Do you know if EE can fabricate your hull from EN26 steel? The hull that Ron A. had fabricated was only 2.5" thick and went full ocean depth with plenty of safety factor. Using the same grade steel in a thickness designed for only 13,000 ft might save a lot of weight.
Greg C

      From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
 To: Personal Submersibles General Discussion <personal_submersibles at psubs.org> 
 Sent: Monday, June 26, 2017 7:54 AM
 Subject: Re: [PSUBS-MAILIST] Pressure Test
  
Alan,That really turned out nice, how did you mould the polyurethane? that stuff sticks like mad. I would leave the white gasket, it looks fine.  Either the gasket thickness is not even or the seat is not perfectly matched to the Lenz. 

    On Sunday, June 25, 2017 10:30 PM, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
 

 Pressure tested my light to 1000 psi for an hour using the water blaster 
& no leaks! I didn't have a pressure relief valve in the system as I do with
my air pressure set up & it was a pain getting the chamber lid off. I had
thought the water blaster would have leaked a bit of pressure but it didn't.
The sealing system for the wires was a 3 layered process; encapsulating the
wires in the epoxy, then coating the insulation for an inch up from where they came 
out of  the epoxy, & over the epoxy with a 2 part heat activated pvc glue that 
they use on inflatable boats. This glue worked a lot better on the pvc insulation
than several others I tried like E61000 (supposed to be better than shoe goo),
3M 5200 & polyurethane.
Over this, to tidy it up & act as a cable support, I moulded polyurethane.
In the attached photos the white ptfe gasket that the lens sits on looks wet
but it is just the compression of the lens against the gasket. I don't like this
from a cosmetic point & may change it. The 2 objects with the light are the
male mould for the polyurethane cable support & the silicone mould for the 
same.
Alan


Sent from my iPad_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   

|  | Virus-free. www.avast.com  |

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170709/011102d5/attachment.html>


More information about the Personal_Submersibles mailing list