[PSUBS-MAILIST] WD - 40

MerlinSub@t-online.de via Personal_Submersibles personal_submersibles at psubs.org
Tue Mar 28 16:22:53 EDT 2017


Seems so. But is much more expensive.
Look for silicon oil oil with a real low cST (centi stokes) 0,65 - 5 (more 
liquid than water) 
Lower cST means less resistance for the rotating part.
 
 
 
-----Original-Nachricht-----
Betreff: Re: [PSUBS-MAILIST] WD - 40
Datum: 2017-03-28T19:47:20+0200
Von: "Brian Cox via Personal_Submersibles" 
<personal_submersibles at psubs.org>
An: "Personal Submersibles General Discussion" 
<personal_submersibles at psubs.org>
 
 
 
Carsten,         Does the silicon oil solve all these problems ?
 
Brian


--- personal_submersibles at psubs.org wrote:

From: "MerlinSub at t-online.de via Personal_Submersibles" 
<personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion 
<personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] WD - 40
Date: Tue, 28 Mar 2017 18:53:22 +0200 (MEST)

On a brushless motor it will maybe work with mineral oil.
On motors with brushes I have bad expierence with that.
Mineral oil is a big problem in a lake if a motor is even a little untight.
 
 
 
-----Original-Nachricht-----
Betreff: Re: [PSUBS-MAILIST] WD - 40
Datum: 2017-03-28T17:15:59+0200
Von: "Brian Cox via Personal_Submersibles" 
<personal_submersibles at psubs.org>
An: "Personal Submersibles General Discussion" 
<personal_submersibles at psubs.org>
 
 
 
Hi Carsten, 
                        I did a small test trying to light the WD40 on 
fire.  It's not as flammable as I thought it would be.  I think they have 
improved it's non-flammability with new formulation. It's still somewhat 
flammable however. 
I will be using a light mineral oil in my motors.
 
Brian
 


--- personal_submersibles at psubs.org wrote:

From: "MerlinSub at t-online.de via Personal_Submersibles" 
<personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion 
<personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] WD - 40
Date: Tue, 28 Mar 2017 07:22:02 +0200 (MEST)

Heat Vapor is may a problem with WD40.
May ensure that the compensating back is big to handle that..
We change to silicon oil for that reason.
 
vbr Carsten
 
 
 
-----Original-Nachricht-----
Betreff: [PSUBS-MAILIST] WD - 40
Datum: 2017-03-28T04:56:46+0200
Von: "Brian Cox via Personal_Submersibles" 
<personal_submersibles at psubs.org>
An: "PSubs" <personal_submersibles at psubs.org>
 
 
 
I just ran one of my motors filled with the WD40.  It seemed to be very 
happy.  I mainly just did it to clean the carbon build up out of the motor. 
 I was surprised how sealed the motor was, it is open at one end where it 
mates to the gear box.  I was able to fill it up without it leaking out 
anywhere.  That could be an issue later when I want the mineral oil to fill 
all the voids.  I might need to actually drill some holes to get some 
circulation . 
 
 
Brian 
_______________________________________________ Personal_Submersibles 
mailing list Personal_Submersibles at psubs.org 
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
<http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles> 
_______________________________________________ Personal_Submersibles 
mailing list Personal_Submersibles at psubs.org
<eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org> 
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
<http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170328/f09fec73/attachment-0001.html>


More information about the Personal_Submersibles mailing list