[PSUBS-MAILIST] WD - 40

Alec Smyth via Personal_Submersibles personal_submersibles at psubs.org
Wed Mar 29 21:34:51 EDT 2017


My lights are done, I put them on Shackleton earlier today and they are
wired through the hull with penetrators. However, the wires end inside the
hull because I'm waiting for the drives to arrive, which will be installed
inside the sub. I was able to test them with a lab type power supply on a
table top, and must say these Bridgelux leds are like a little sun in a
can, I love them. These two lights I made are 5K lumens, and I already have
10K lumen Bridgeluxes which I bought by mistake. So I'll test these, and
probably make another set with those more powerful ones. If I do, the 10Ks
will be the forward lights and the 5Ks will be oriented out to the sides
for "peripheral vision". A dimmable driver is sounding like a good idea, or
maybe just sunglasses!


Best,

Alec

On Wed, Mar 29, 2017 at 9:10 PM, Alan via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Thanks Hank,
> Alec has been making good progress with Cliff's light.
> Last I heard 2 housings were being anodised.
> Any update Cliff / Alec ?
> Alan
>
>
> Sent from my iPad
>
> On 30/03/2017, at 1:30 PM, hank pronk via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> You will be our go to guy for lighting!
>
>
> On Wednesday, March 29, 2017 6:15 PM, Alan via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
>
> Still building lights Hank,
> have built a couple of housings but are doing a third revision &
> hopefully this one will be perfect. I am pretty happy with how it's going.
> Am getting a different LED driver made up with PWM dimming.
> Got off the motor project temporarily as my brother wanted one of
> the lights for his boat. 😐
> Alan
>
> Sent from my iPad
>
> On 30/03/2017, at 12:35 PM, hank pronk via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Alan,
> Are you back to work on your motor?   or are you still building lights?
> Hank
>
>
> On Wednesday, March 29, 2017 4:44 PM, hank pronk via Personal_Submersibles
> <personal_submersibles at psubs.org> wrote:
>
>
> Thanks' Greg
>
> Alan, my answer is who cares if some water gets between the seals.  The
> important part is to keep the oil inside the motor.  When the motor starts
> up at the surface, there is significant centrical force that pushes the oil
> out with the seal in its original orientation.  I should actually remove
> one of the seals and just have one seal holding oil in, just like a
> submersible well pump has.  Those pumps are VERY reliable.  Now having said
> all this, I could be wrong ;-)   Stay tuned for test results.
> Hank
>
>
> On Wednesday, March 29, 2017 4:31 PM, Alan via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
>
> How are you doing that Hank?
> Are you compensating the gap between the two seals?
> Otherwise you are in the same situation as the Minn kota motors
> where one of the two seals will fail when you go beyond it's depth
> rating.
> Cheers Alan
>
> Sent from my iPad
>
> On 30/03/2017, at 10:40 AM, hank pronk via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Greg,
> Good points, but I personally am not ready to give up on oil filling.  I
> have reversed one of the two seals in my new motors for Elementary.  One
> seal keeps the oil in and one seal keeps the water out.  I am confident
> this in addition to the compensation system will make for a clean leak
> proof set up.  The ice is off the lake by my house, so my test lake should
> be open in a week or so.  I will know then if my idea works.
> Hank
>
>
> On Wednesday, March 29, 2017 7:03 AM, james cottrell via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> I have to say, I no longer think that WD40 is the best for compensating
> things underwater. Over time it causes plastics and rubber to harden and
> become brittle.
> Silicone oil is better but the other problem with oil compensation in
> general is that the smallest drop/leak makes a very visible oil slick
> around your sub (not good). Most guys are using trolling motors and they're
> not really tight enough to hold thin oil without leaks.
> Back in the 90s I was using air compensation- and it actually worked
> really well. As far as I know, Karl Stanley has also been using air
> compensation for a long time without problems.
> It's a clean system that's not hard to set up and a small bottle of air
> lasts for many dives.
>
> Greg C
>
>
> ------------------------------
> *From:* "MerlinSub at t-online.de via Personal_Submersibles" <
> personal_submersibles at psubs.org>
> *To:* Personal Submersibles General Discussion <
> personal_submersibles at psubs.org>
> *Sent:* Tuesday, March 28, 2017 12:55 PM
> *Subject:* Re: [PSUBS-MAILIST] WD - 40
>
> On a brushless motor it will maybe work with mineral oil.
> On motors with brushes I have bad expierence with that.
> Mineral oil is a big problem in a lake if a motor is even a little
> untight.
>
>
>
> -----Original-Nachricht-----
> Betreff: Re: [PSUBS-MAILIST] WD - 40
> Datum: 2017-03-28T17:15:59+0200
> Von: "Brian Cox via Personal_Submersibles" <personal_submersibles at psubs.
> org>
> An: "Personal Submersibles General Discussion" <
> personal_submersibles at psubs.org>
>
>
>
> Hi Carsten,
>                         I did a small test trying to light the WD40 on
> fire.  It's not as flammable as I thought it would be.  I think they have
> improved it's non-flammability with new formulation. It's still somewhat
> flammable however.
> I will be using a light mineral oil in my motors.
>
> Brian
>
>
>
> --- personal_submersibles at psubs.org wrote:
>
> From: "MerlinSub at t-online.de via Personal_Submersibles" <
> personal_submersibles at psubs.org>
> To: Personal Submersibles General Discussion <personal_submersibles at psubs.
> org>
> Subject: Re: [PSUBS-MAILIST] WD - 40
> Date: Tue, 28 Mar 2017 07:22:02 +0200 (MEST)
>
> Heat Vapor is may a problem with WD40.
> May ensure that the compensating back is big to handle that..
> We change to silicon oil for that reason.
>
> vbr Carsten
>
>
>
> -----Original-Nachricht-----
> Betreff: [PSUBS-MAILIST] WD - 40
> Datum: 2017-03-28T04:56:46+0200
> Von: "Brian Cox via Personal_Submersibles" <personal_submersibles at psubs.
> org>
> An: "PSubs" <personal_submersibles at psubs.org>
>
>
>
> I just ran one of my motors filled with the WD40.  It seemed to be very
> happy.  I mainly just did it to clean the carbon build up out of the
> motor.  I was surprised how sealed the motor was, it is open at one end
> where it mates to the gear box.  I was able to fill it up without it
> leaking out anywhere.  That could be an issue later when I want the mineral
> oil to fill all the voids.  I might need to actually drill some holes to
> get some circulation .
>
>
> Brian
> _______________________________________________ Personal_Submersibles
> mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/
> listinfo.cgi/personal_submersibles
> 
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170329/5c2522c2/attachment-0001.html>


More information about the Personal_Submersibles mailing list