[PSUBS-MAILIST] Heads Question

Thu Sep 21 07:55:43 EDT 2017

 Dan,That is a good idea, I have done a side bend test on a sample quite a while ago but that was 1\2 inch material so pretty easy to bend.  I just built a jig to hold it from tipping over.   My Ultrasound guy is a portable operation, and I am not sure he can do the bending.  I am sure there is a place in nearby Calgary or Edmonton.  The sample is quite big at 16 inches in diameter, so I have a 16 inch weld.  You already know that I have to do a bend myself because that is the kinda guy that I am ;-)    I can use 1\2 the sample for my own testing and the other half can be done in a proper facility.  I am really glad now that I welded the entire thing and then cut out the port. Hank

    On Wednesday, September 20, 2017, 7:48:29 PM MDT, Daniel Lance via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  

 Hank,I would suggest that you take the hull section that was cut from your port frame and send it to a Materials Test Lab . ( probably the same company that is going to do your ultrasound can do it ) . Have them do a " Guided Bend Test " on the coupons they cut from it .  If you have it done professionally you will have unequivocal proof of your weld integrity . The lab is well practised in this type of test and has all the proper equipment . Without the coupon guide/bending jig that fits in the hydraulic press it is difficult for an individual to get reliable results .  When you send your sample to the lab ask them to do " Side Bends " on the coupons that they cut from your welded plate instead of  "Face" and  "Root" bends . Performing side bends puts you solidly in the realm of the rigorously high standards of ASME PVHO .  With a design depth of 914 meters (3000fsw) you are  in the big leagues now and the peace of mind that comes from a professionally  done test will be priceless .Dan
On Wed, Sep 20, 2017 at 12:58 PM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

 River,I agree the pressure test is of little value determining  fatigue life.  My goal was to establish if the engineering is good and if the welds would fail.  Mission accomplished.  Before the pressure test I was going to do an ultrasound test but decided to do a preliminary dye penetrant test.  I figure why spend 1,000 dollars on a test that needs to be repeated after the pressure test.  My next step is the ultrasound test and I have a hull section that was cut out for the port frame with the weld going through the middle.  I will cut that piece up and bend it to prove the weld quality.Hank
    On Wednesday, September 20, 2017, 6:18:15 AM MDT, Sean T. Stevenson via Personal_Submersibles <personal_submersibles at psubs. org> wrote:  

Fatigue issues in weldments typically arise as a result of the geometry of the weld, where fatigue sensitive details such as doubler plates, sharp interfaces, inherent "cracks" at the apexes of partial penetration welds, overlapping weld toes etc. cause local amplification of the service stress ranges. Pressure hulls are inherently resistant to fatigue as a result of the mandated geometries, CJP welds, and barring the high strength alloys, the generally tougher nature of e.g. ASTM A516 Gr. 70 steel. I might go as far as to say that a PSub is unlikely to see enough high stress cycles within its lifetime to justify worrying about fatigue at all. Indeed, ABS only requires a fatigue analysis under specific conditions:

>From the ABS rules (2017):
Section 6/9:

Fatigue  (2002) A  fatigue analysis  is  to  be submitted  when  it is  anticipated  that the life time  full range pressure  cycles  N will exceed  that obtained  from  the following  equation: 

N = [1160(3000  –  T)/(Kfτ  –  14500)]^2 

where

T = temperature  in  degrees  C  (degrees  F)  corresponding  to  application  of  the  cyclic  or repeated stress
K  =  5688 SI/MKS units (4  U.S.  units) 
fτ = range  of  cyclic stress  kg/mm2  (lb/in2) 

Pressure cycles  of  less  than  full  pressure are to  be included  in  N  in  the ratio  p/P  where  p  is  the  actual pressure of  the  cycle  under  consideration  and  P  is  the design  pressure. 

Sean

On September 19, 2017 12:39:42 PM MDT, River Dolfi via Personal_Submersibles <personal_submersibles at psubs. org> wrote:
I'm sure Sean can also speak at length about this, but a single pressure test gives no information about fatigue life. The size of flaw in a weldment (and all welds have flaws) may not be constant over the service life of the vessel. Weld material with sufficiently low fracture toughness (aided by low temperatures) will have it's flaws elongate with each cycle, as predicted by the Paris Law of crack propogation, until eventually reaching a critical size and fracturing. This is compounded rather unpredictably by the corrosion typical of a marine environment. 

All I know is that I know nothing. But sometimes I think we should pool our money and buy an ultrasound machine...

-River J. Dolfi
412-997-2526rdolfi7 at gmail.com
On Tue, Sep 19, 2017 at 1:29 PM, via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

Send Personal_Submersibles mailing list submissions to
        personal_submersibles at psubs. org

To subscribe or unsubscribe via the World Wide Web, visit
        http://www.whoweb.com/mailman/ listinfo.cgi/personal_ submersibles
or, via email, send a message with subject or body 'help' to
        personal_submersibles-request@ psubs.org

You can reach the person managing the list at
        personal_submersibles-owner@ psubs.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Personal_Submersibles digest..."

Today's Topics:

   1. Re: Heads Question (hank pronk via Personal_Submersibles)

------------------------------ ------------------------------ ----------

Message: 1
Date: Tue, 19 Sep 2017 17:23:42 +0000 (UTC)
From: hank pronk via Personal_Submersibles
        <personal_submersibles at psubs. org>
To: Rick Patton via Personal_Submersibles
        <personal_submersibles at psubs. org>
Subject: Re: [PSUBS-MAILIST] Heads Question
Message-ID: <674133299.2545129. 1505841822312 at mail.yahoo.com>
Content-Type: text/plain; charset="utf-8"

 Dan, Rick,I would argue that you guys are indeed experts. ?I am not,,,but,, I am an expert experimenter and tester . ?My welder has a 60% duty cycle and I have welded and tried to destroy the weldments and actually wrecked a jack trying . ?I test welded and bent and tortured material and not once did a weld break. ?Again you guys are the experts but Elementary 3000 had 392,500 lbs trying to push the hatch through the opening with no issues at all. ?I can talk about my welding all day long but it is the pressure test that says it all. ? I would have tested it a lot higher but that was the limit of the chamber.How can you explain my pretty welds holding ?6,500 lbs per inch? ?If my welder can only weld sheet metal, why did it not fail? ? I am a pretty luck guy, maybe that is it ;-)Hank

    On Tuesday, September 19, 2017, 11:00:50 AM MDT, Rick Patton via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Mig welds can be deceptive sometimes. I have seen very pretty factory fellet mig welds come threw my doors in both aluminum and mild steel where the weld had completely let go of one of the two sides due to lack of penetration.? The prep or process wasn't done correctly but yet it still looked good.?This is not the case with TIG or stick. There is a saying amongst Welders that if a stick weld looks good, it probably is. If it is a critical weld, you still want to X ray or UT it but you will always have penetration on both sides unlike mig. Beginners and novice welders sometimes gravitate towards Mig as it is easier than stick but a pressure vessel that you are going to be in, then l would stick with stick "pun intended " or if your insistent on Mig, have it done professionally or make darn sure your using the correct equipment as Dan inferred.?Rick?
On Tue, Sep 19, 2017 at 9:08 AM Daniel Lance via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

Hank,I do not in any manner consider myself an expert .? I am just relying on what I learned during 36 years in the welding industry . My motto is if a person keeps the right attitude he or she can learn something new everyday ! ?:)Dan
On Tue, Sep 19, 2017 at 7:43 AM, hank pronk via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Dan,I could tell you all about the million tests I did after loading the wire into my shiny welder and i could talk about the results, but, you are the expert and we should take your advice.? No question about it, i would not want to encourage anything else.Hank
    On Tuesday, September 19, 2017, 4:52:00 AM MDT, Daniel Lance via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 ?Since the topic has come up in this current thread I want to state for the record that I would encourage anyone contemplating using the " Short Arc MIG welding process " to weld their submarine's pressure hull to consult a licensed qualified , experienced ?Welding Engineer before doing so ( and NOT the Welding machine manufacturers sales rep) . MIG ( short arc ) should only be used on light gauge metals ( .1875" and below ) , when used on heavier thickness steel it produces welds brittle in nature and ultimately prone to cracking . This process is ill suited for building pressure vessels especially ones intended for PVHO . Steel has an inherent tendency to become brittle at low ambient temperatures ( think a northern latitude lake where the bottom temperature could possibly be in the upper 30s , 40s or 50 degrees F range ) add to that a welding process well documented to produce brittle welds and then factor in a bottom pressure of hundreds maybe even t! housandsof pounds p!
 er square inch. Chances are very good that the hull won't fail on the first dive or hydro test but basically what you have is the proverbial " one bullet in the revolver " situation ?leading to a false sense of security . ? ?Like I mentioned earlier consult a "Licensed" qualified , experienced Welding Engineer and heed his advice before loading that spool of wire in your shiny new welding machine or hiring the "expert welder from down the street . Like the old saying goes " what you don't know can hurt you " .Dan Lance
On Mon, Sep 18, 2017 at 2:57 PM, hank pronk via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Alec,Yup, I have heard it all from the stick welding only crowd.? I hear all the time "I like to turn it up and burn it in" ?or ?" I like to crank er up" ?LOL.The fact is, too much penetration is bad because you introduce parent metal into the filler metal, and that is bad.? You need sufficient penetration and I have no problem achieving that.? I mig welded Elementary 3000 and it is 1 inch thick, with no problem, and it has been to 1,250 psi.Hank
    On Monday, September 18, 2017, 10:13:50 AM MDT, Private via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Yep, I think you're probably right! My only concern would be using mig on a pressure vessel though. I'm not an expert, but what I've always heard from those who are is that it's for high-productivity jobs but not for jobs like full penetration where quality trumps speed.
On Sep 18, 2017, at 7:56 AM, hank pronk via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Alec,I like a bevel on both sides, and I also do a mig pass on the inside then grind outside as you do.? When your welding such light material, the external grind job is creating the same shape weld grove as if you started with a bevel on both sides.? Same difference really.? The big difference is guys like Rick and Dan can do this all at ounce because they are professional welders.Hank
    On Sunday, September 17, 2017, 8:33:43 PM MDT, Alec Smyth via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

 Here's the method I used. The starting point is a bevel with the sharp end of course on the ID and the wide end of the wedge on the OD. An air gap of about 1/8" is left between the two parts.
1) TIG weld the root pass, from the inside of the hull, plugging the air gap.?2) Grind with an angle grinder from the outside into the root pass. Use a 1/4" wheel on the angle grinder. You need to get a clean shiny U shaped channel, pure like-new metal, with no visible discontinuities whatsoever.3) Stick weld from the outside building up layers until meeting the plate thickness.
Perhaps a double bevel would be needed for very thick material. The method I'm describing, I've used on material up to 1/2" with no problem.
Dan, if I'm talking rubbish please set me straight!

Best,
Alec?

On Sun, Sep 17, 2017 at 9:52 PM, Rick Patton via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

Definitely want to bevle both sides. If you don't, your wire/stick/Tig will short out way too soon becoming molten and not reaching the ID of the hull and you will have to do a lot of back gouging before reaching your first pass.Rick?
On Sun, Sep 17, 2017 at 3:54 PM Brian Cox via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

I have found that I get a better weld if both sides are beveled .?Brian

--- personal_submersibles at psubs. org wrote:

From: Private via Personal_Submersibles <personal_submersibles at psubs. org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs. org>
Subject: Re: [PSUBS-MAILIST] Heads Question
Date: Sat, 16 Sep 2017 19:30:01 -0400

Hi David,
Absolutely, you want it with the flange. Any impression otherwise was my "mind typo" that I was trying to clarify in the second email. If you can avoid beveling it yourself, however, it'll save quite a job. You only need one of the two edges beveled, either the head flange or the end of the cylinder it will mate to, and it doesn't matter which. Greg has a good point, but I suppose a key factor is whether you'll be welding yourself or contracting out. I learned to do my own, with an awful lot of help from Dan Lance.
Best,
Alec
On Sep 16, 2017, at 12:50 PM, james cottrell via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

Hi David,
In my experience it was cheaper and faster to hire an ASME tank fabricator to produce a steel cylinder with the head (or heads) welded on. Mine came machine welded with an ASME code stamp.?If your design will feature external frames, ask them for both heads welded on. If your design will feature internal frames (done later) ask them to weld one end only. This will be cheaper in the long run and better built. It's hard to beat pressure vessel code machine welding. Specify NO backing strips.
Another tip- call it a "vacuum tank".
Greg Cottrell

      From: David Colombo via Personal_Submersibles <personal_submersibles at psubs. org>
 To: Personal Submersibles General Discussion <personal_submersibles at psubs. org>
 Sent: Saturday, September 16, 2017 12:20 PM
 Subject: Re: [PSUBS-MAILIST] Heads Question

Hi Alec, I just spoke with the company that Roberto mentioned here in California to place an order for dished head for the SeaQuestor. I will be using the 36"OD x .375 A516-70 steel what they call Elliptical 2:1 Ratio ASME Code Type. It comes with a 2" flange which is really a 36" od ring shape as part of the forming. This would mate up to the 36"OD first hull section. I'm thinking that this would give me the best welding condition with two matched surfaces that I would bevel for full pen welding. I'm curious why not to have the flange? ? My cost here is $480.00 + $96 to have it shipped to northern California from southern California. even though its only a nine hour drive one way, I think my time would be worth more than $5 hr to pick it up. LOL Unless of course its cheaper in Canada (Hank), I might make the trip and could serve as support crew for the Gamma. Any thoughts out there from fellow Psubers would be appreciated.

Best Regards,
David Colombo

804 College Ave
Santa Rosa, CA. 95404
(707) 536-1424
www.SeaQuestor.com

On Fri, Sep 15, 2017 at 2:28 PM, Alec Smyth via Personal_Submersibles <personal_submersibles at psubs. org> wrote:

Ugh, mental typo. I meant "un-beveled" and "bevel them yourself", not "un-flanged" and "flange them yourself".
!!!!!!!
On Fri, Sep 15, 2017 at 5:25 PM, Alec Smyth <alecsmyth at gmail.com> wrote:

Hi Roberto,
I believe the short description for what you need is flanged, beveled, and code. You could get them unflanged, but it takes quite a while to make a flange with an angle grinder. The flanges if I recall are 2". Do set up a project page or something so we can follow progress!

Best,
Alec
On Fri, Sep 15, 2017 at 5:07 PM, roberto alvarez via Personal_Submersibles <personal_submersibles at psubs.o rg> wrote:

Hi, lost the plans cd for the k250, i am? interested in the? head selection, i found a seler in california and have?flanged ,beveled ,code, non code,
Will apreciate your support in this ( until i found the plans cd )
______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.or g
http://www.psubs.org/mailman/l istinfo.cgi/personal_submersib les

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles

______________________________ _________________Personal_ Submersibles mailing listPersonal_Submersibles@ psubs. orghttp://www.psubs.org/ mailman/ listinfo.cgi/personal_ submersibles__________________ ____________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/ pipermail/personal_ submersibles/attachments/ 20170919/0b371519/attachment. html>

------------------------------

Subject: Digest Footer

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.whoweb.com/mailman/ listinfo.cgi/personal_ submersibles

------------------------------

End of Personal_Submersibles Digest, Vol 51, Issue 82
****************************** ***********************

Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles

______________________________ _________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs. org
http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170921/6c09a25d/attachment-0001.html>