[PSUBS-MAILIST] home made actuator

hank pronk via Personal_Submersibles personal_submersibles at psubs.org
Sun Aug 12 07:51:48 EDT 2018


 Brian,I agree the acme thread rod would work well.  In fact, that is where I started with the idea.  I would need a gear box to up the torque and I am trying to keep it simple to build.  If the other two options don't work out, I will be back to the acme rod.Hank
    On Sunday, August 12, 2018, 5:05:26 AM MDT, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
 Hank,that blue robotics motor was 4.5 in lbs torque. (.38 ft lbs) So you wouldprobably have to gear it anyway, or buy a motor controller that couldhandle a lot of amps. They sell motor controllers for that motor. The only thingthat can be a bit problematic with the brushless motor controllers is that if they are designed for the hobby market they are normally operatedvia a transmitter & receiver not a potentiometer. There are electronicsto get round that.  I just bought a pressure sensor / temperature sensor & underwater switchoff Blue Robotics. I am sure that actuator motor will be DC.I will be interested to hear how you get on with it.Alan
On 12/08/2018, at 10:33 PM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:


 Alan,That is a very slick motor alright, but it needs a controller.  You know how I try to avoid electronic components whenever possible.  Also i am trying to keep the cost down by using parts that I already have.  I have a satellite dish actuator and I have a trolling motor on the shelf.  I am picking up the actuator today from the shop and bringing it home to tear down.  I am quite excited that it might be DC.Hank
    On Sunday, August 12, 2018, 3:57:07 AM MDT, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
 Hank,what about using one of these 350W brushless underwater motorsfrom blue robotics!https://www.bluerobotics.com/store/thrusters/m200-motor-r1/They sell them as rov motors & for that use I have reservations, as the propcould drive sand etc in to the sealed windings & possibly wear through theinsulation. But for turning a threaded rod that moved your trim weight theymight be fine. Certainly save a lot of stuffing round modifying a linearactuator. I saw these motors on a reasonably expensive rov recently.Cheers Alan
On 12/08/2018, at 9:45 AM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:


 Alan,I just had a look at the one you found, and I did not realize they were DC.  I thought they were AC, well that is awesome!Thanks"Hank
    On Saturday, August 11, 2018, 3:40:12 PM MDT, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
  Alan,  I think they are probably song enough, I just swap the AC motor out.  I don't need 400 lbs to do the job but I need 400 lbs of ballast.  I am actually planning to make a moving cradle that also carries the oil filled batteries.  I don't know how much force it will require, but, the cradle will be on rollers to make it easy.I am ready to test for balance, so I will have to switch over to building a test pool.  My plan to put an in ground pool in my new shop is out now because there is a giant lathe in the way.Hank
    On Saturday, August 11, 2018, 3:34:01 PM MDT, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
 Hank,my first thought was satellite dish actuator.This one is claiming 500lb capacity.https://www.ebay.com/itm/Venture-18-Inch-Linear-Actuator-36V-Jack-Arm-with-Saddle-Clamp-Satellite-Dish-/271574942987But you wouldn't need that with horizontal travel. Any idea what force ittakes to pull / push it? I assume it is external.Just wondering why you need 400lb!  Cheers Alan

On 12/08/2018, at 8:54 AM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:


Hi All,I am in need of a long stroke electric actuator to move my 400 lb trim weight.  Of coarse I want to make one.  I am planning to either add a oil filled trolling motor to a trailer jack or mount the trolling motor to a satellite dish actuator.  I have not dismantled the satellite dish actuator yet to see if it can handle the job.  I think it can but I will see.  Anyone have another idea?Hank

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20180812/5a37480d/attachment-0001.html>


More information about the Personal_Submersibles mailing list