[PSUBS-MAILIST] Trailer Issue

Jon Wallace via Personal_Submersibles personal_submersibles at psubs.org
Tue Jul 31 14:32:40 EDT 2018


I found these.  Thinking about getting rid of the tandem spring axles and go to a single torsion type.  Reviews on these are excellent.

Timbren Axle-Less Trailer Suspension - 4" Drop Spindle w/ Brake Flange - Regular Tires - 7K Tim

  
|  
|   
|   
|   $ 898.20   |    |

   |

  |
|  
|   |  
Timbren Axle-Less Trailer Suspension - 4" Drop Spindle w/ Brake Flange...
 The Axle-Less system provides a smooth, quiet, safe ride and can eliminate the need for an axle. Suspension unit...  |   |

  |

  |

 


      From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
 To: Jon Wallace via Personal_Submersibles <personal_submersibles at psubs.org> 
 Sent: Tuesday, July 31, 2018 1:29 PM
 Subject: Re: [PSUBS-MAILIST] Trailer Issue
   
 Jon,Your problem is not weight distribution, your hitch on your truck is too low.  My trailer is the same, because the hitch is low from loading the truck.  Also that long trailer does not need 10% hitch weight.  Raise your hitch level with the trailer jack and you will see the spacing even out.Hank
    On Tuesday, July 31, 2018, 9:59:18 AM MDT, Jon Wallace via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
 
Took the K-600 out on the road for the first time on the aluminum boat trailer I have been modifying.  Destination was a weigh station about 20 miles away and the empty submarine came in at 3065 pounds.  Towing was effortless EXCEPT:
Attached is a photo of the suspension equalizer.  The front axle is left, rear axle right.  The submarine placement needs to be almost directly over the front axle in order to get a decent tongue weight of about 10% to prevent sway while towing.  However, you can see that the front side of the suspension equalizer is quite a bit higher than the rear, and after dynamic loading on the road (going over a pothole or two) that spring eye and shackle actually "tops out" or sits against the trailer frame making for a very rough trailer ride.
If I placed the bulk of the submarine over the mid-point between the two axles, theoretically to spread the load equally between them, I would essentially have no tongue weight so I don't see that as an option.  I could always add some extra weight at the front to get some tongue weight but dive ready I will be close to the weight limit of the sub and trailer so may not have much wiggle room for extra additional weight.
Other options?  The shackles are 3.5 inch long, which is longer than a typical shackle, but I think designed that way to get the trailer frame as low to the ground as possible.  I could shorten the shackles to provide more head room between the spring eye and the trailer frame but I hate to do that work only to find out that it isn't enough and the equalizer just cocks more to the front and allows the spring eye to reach the frame again.  It would also end up raising the trailer higher overall which I want to avoid if I can, for purposes of launch and recovery.
I thought about stronger leaf springs but I don't think the springs are the problem.  The problem is that the load is primarily concentrated on the front axle and the equalizer allows the spring to pivot, to compensate.  So I don't see stronger springs preventing this.
I have also thought about "locking" the equalizer in place which would subvert the purpose of the equalizer.
Suggestions welcome
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles


   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20180731/556dfbb4/attachment-0001.html>


More information about the Personal_Submersibles mailing list