Hi Dariusz,
I'm not an expert on the subject but am somewhat in the know because of
my
desire to have a large window in a price range that I can afford and
still
be able to get 1000 foot depth.
Sheet acrylic as far as I know is not available in widths of greater than
48
inches. In a dome shape this limits you to about 39 inch diameter.
I had Greg make up a dome 39 inches diameter and 2.5 inches thick. I then
had two rings formed to make the seat area and have welded them together.
This seat has now been tacked to the transition cone which is 11 inches
tall
and transitions from the sub 48 inch OD to the 42 inch OD of the window
seat.
When this is finish welded I will take the assembly to a machine shop
that
is capable of handling this piece and machine the seat area. In my case
the
cone is 3/4 inches thick and the rings of the seat are 1.5 inches thick
the
forming was quite expensive.
The steel work to accomodate the window is more expensive than the window
itself. I will have a very nice window when complete, but the entire
window
and seat/cone will be close to $9,500.00.
While this is a lot of money, it gives me most of what I want. I
originally
wanted a 48 inch dome, but the cost would have put a stop to my project.
If I am correct in saying 48 inch diameter sheet is the maximum you do
not
the option of making a 59 inch diameter flat window, as I would never do
this by overlaping and bonding sheets.
I no this is not what you want to hear, but I think my experience is
accurate.
Best Regards,
Jim K
----- Original Message -----
From: "Dariusz Hoffmann" <darekhoffmann@gmail.com>
To: <personal_submersibles@psubs.org>
Sent: Tuesday, September 09, 2008 6:04 AM
Subject: [PSUBS-MAILIST] Dome alternative - flat acrylic endcap
> Hello.
> Apart from acrylic dome endcap I am considering an alternative - flat
> acrylic endcap. This would be a flat window about 59" (150cm) in
> diameter,
> 10" (25cm) thick. That kind of front side would be very inefective
> hydrodynamically. So there should be another acrylic layer, a thin dome
> with holes in it to allow flooding it while submerging. This would
> increase the hydrodynamic effectivness and would also help protecting
> the
> main window. I think this could be cheaper than purchasing 59" od, 3"
> thick dome for the main window. What are disadvantages of that
> solution?
>
> Thanks
> d.
>
>
>
> ************************************************************************
> ************************************************************************
> ************************************************************************
> The personal submersibles mailing list complies with the US Federal
> CAN-SPAM Act of 2003. Your email address appears in our database
> because either you, or someone you know, requested you receive messages
> from our organization.
>
> If you want to be removed from this mailing list simply click on the
> link below or send a blank email message to:
> removeme-personal_submersibles@psubs.org
>
> Removal of your email address from this mailing list occurs by an
> automated process and should be complete within five minutes of
> our server receiving your request.
>
> PSUBS.ORG
> PO Box 53
> Weare, NH 03281
> 603-529-1100
> ************************************************************************
> ************************************************************************
> ************************************************************************
>
>
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************