[PSUBS-MAILIST] conical hatch seat troubles

Thu Dec 1 12:38:23 EST 2016

Brian,I test for fit with the o-ring out.  Don't worry about yours, flat hatches will bend like butter.  My K350 hatch had a .04 in dip in it and it flattened out right away.  You just need a bit more weight pulling on your hatch.  Gamma used to drip on every dive from the hatch seal.  I made an adjustment to tighten the one dog and that cured it.  How hard is your o-ring?Hank 

    On Thursday, December 1, 2016 9:38 AM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

 Hank,   Is that with out the o ring installed?     Now you've got me worried,  I had to give my hatch a little help by sitting on it when I pulled a vacuum on it.  I'm not sure why exactly I'll have to check again. Brian

--- personal_submersibles at psubs.org wrote:

From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] conical hatch seat troubles
Date: Thu, 1 Dec 2016 15:22:15 +0000 (UTC)

Carsten,I can turn it but it is very heavy and wants to wobble in the seat or climb out because it is conical.  It is a solution though!   Is it necessary though?Hank 

    On Thursday, December 1, 2016 4:56 AM, "MerlinSub at t-online.de via Personal_Submersibles" <personal_submersibles at psubs.org> wrote:

  Hank can you turn the hatch in the seat ? 
 3 Peace of sandpater all 120 degree and turning and water dripping from a hose or later Piston Paste between hatch and seat ? Making a leaver on the hatch and running the hole day around the submarine?30 Turns clockwise and 30 turns anticclock. Than again. Do you have friends liking hard walking? Its a good evening with two friends and some sixpacks of beer It was exact that way Emile and I making the final seat of a dome seat.  vbr Carsten     -----Original-Nachricht-----Betreff: [PSUBS-MAILIST] conical hatch seat troublesDatum: 2016-12-01T12:00:56+0100Von: "hank pronk via Personal_Submersibles" <personal_submersibles at psubs.org>An: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>   Hi All,I have a problem with my conical  hatch seat.  I have discovered that I have a .005 in gap between the hatch and seat in two spots.  It seems the seat is oval with a gap at each end.  I have no way of measuring this other than placing video cassette tape ribbon strips between the hatch and seat.  What I do is, I cut the ribbon into 3 inch strips, then tape them in place so they are hanging over the seat.  I put one every two inches, then close the hatch.  The ribbons are then trapped tight in the gap.  if the ribbons can pull out then there is a gap.  Sure enough, I can remove one at the front, so I put two ribbons on top of each other in that spot and it still pulls out.  I add another making 3 ribbons thick and it is tight.  Then I tried doubling one ribbon in the front and one opposite in the back and they were tight.  The conclusion is that the seat is oval by .005 in at each end.  I put the hatch back in the lathe and re-faced it, to be sure it is not the hatch.  It is the seat, it seems my flange facing machine is not perfect-not a big surprise.  This is still very good for a portable home made tool.I don't know if this a problem or not, how accurate does this have to be?  Will the assembly simply bend?  My feeling is the hatch and seat will deform to match under pressure.  To put it into perspective, I just measured a hair and that is .01 in. the same as the total gap combined.Hank
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

   _______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20161201/d75e4ee8/attachment.html>