[PSUBS-MAILIST] air compensation

hank pronk via Personal_Submersibles personal_submersibles at psubs.org
Sat Dec 9 07:53:01 EST 2017


 Alan, thanks'I just googled an air flow chart, and the .125 air hose can supply .5 scfm at 5 psi.  So now I have to calculate the volume change in the actuator  at my dive rate and see if .5 scfm will supply each actuator.  I was not worried about the line supplying the actuator when it was operating.  My concern was for the line to keep up while descending.  I also thought I might need a relief valve on each actuator for rapid ascents.  Hank
    On Saturday, December 9, 2017, 5:25:45 AM MST, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
  Alan,I assumed that the air pressure at the out port of the regulator is 4 psi above ambient.  My concern is,, will the .125 air line supply air fast enough at 4psi to maintain 4psi above ambient inside the actuator.   Hank
    On Friday, December 8, 2017, 10:01:31 PM MST, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  
 
 Hank,you will have the internal space of your actuator to equalise, whichshouldn't be a problem as this will be slowly equalised as you descend.Then you have the piston going out during manipulator use, & there will be air goingin to fill that void. If you are running either off a 1st stage regulator or a relievingregulator like Cliff's, the air will be kept at ambient & it will only be that smallflow in to the space the piston has vacated. You could estimate the internal volume change by using an on line cylinder volume calculator & plugging in the piston diameter & the difference in length it changes as it protrudes.If the actuators full stroke takes (as an example) 4 seconds at full speed, &the volume is 100ml, you could then run air through your intended hose at your supply pressure (130 psi for scuba regulator) in to a small crushed plastic bag, & see if it canat least fill the bag with 100ml of air in 4 seconds. Have done similar for rough estimates.Or just blow through the hose in to a plastic bag ( like lots of people do at Christmastime) & you might think yep this will do with 130psi behind it.BTW on A relieving regulator the orifice is pretty small & in Cliff's case it is ventingthe internal volume of his 4 thrusters in the last 30ft of ascent.Cheers Alan
Sent from my iPad
On 9/12/2017, at 4:37 PM, hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:


Hi All,I am new to air compensating so I need to know if the air line size to each of my actuators is critical.  To save money I want to recycle  the high pressure nylon tubing that is used for hydraulic lines on my hydraulic arm.  The nylon air lines  are a bit over .125 IDthanks'Hank 

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20171209/ec8f2b12/attachment.html>


More information about the Personal_Submersibles mailing list