[PSUBS-MAILIST] Shaft Seals

[Rick Patton via Personal_Submersibles]

I was asked about my gas analyzer the other day which I've had for 11 years
and after checking into it, the company "Biosystems Inc." had been sold to
Honeywell and my unit was discontinued and can't even get it worked on or
buy new sensors as of last year. It did 4 gasses but C02 wasn't one of them
as I used it for something else.
Brandt instruments in Prariyville LA. has a system that does only O2 & C02
only and sells for $1,205 for the Alkalide battery set up. They said that
the replacement sensor for the Co2 was about $1,000 though!
I guess I,ll use my old one now as an expensive paper weight! 😬

Rick

On Wed, Feb 1, 2017 at 5:23 PM, Brian Cox via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Interesting ! ,  found their website
>
> --- personal_submersibles at psubs.org wrote:
>
> From: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org
> >
> To: "Personal Submersibles General Discussion" <
> personal_submersibles at psubs.org>
> Subject: Re: [PSUBS-MAILIST] Shaft Seals
> Date: Wed, 1 Feb 2017 18:41:50 -0800
>
>
> Speedy sleeve ?
>
> --- personal_submersibles at psubs.org wrote:
>
> From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.
> org>
> To: Personal Submersibles General Discussion <personal_submersibles at psubs.
> org>
> Subject: Re: [PSUBS-MAILIST] Shaft Seals
> Date: Thu, 2 Feb 2017 02:15:34 +0000 (UTC)
>
> Brian,
> Make a speedy sleeve.  No biggy
> Hank
>
>
> On Wednesday, February 1, 2017 6:45 PM, Brian Cox via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Hi All,
>                 Got myself into bit of a bind,  my 2.5" OD by 1" ID shaft
> bearing is fine, but it turns out that they don't make a seal that exact
> size.  They have under and over ,  so what I might do is epoxy the two
> shaft seals together so I can get to where I need to be.   They make a
> 2.5"OD by 1.25"ID  seal;   on my next motor pod I may change the propeller
> shaft to 1.25" just to make things easier !
>
> Brian
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
> _______________________________________________ Personal_Submersibles
> mailing list Personal_Submersibles at psubs.org http://www.psubs.org/mailman/
> listinfo.cgi/personal_submersibles
> _______________________________________________ Personal_Submersibles
> mailing list Personal_Submersibles at psubs.org
> <http:///eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org>
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20170202/0fed0511/attachment-0001.html>